Hp media vault and windows 7




















Apache Log4j Update Please see this document here for current information regarding the Apache Log4j vulnerability. Need Windows 11 help? In the Configure section you have choices to. Downloads and installs updates on the server in the background. If necessary the server will automatically reboot. Your computer notifies you that an update has been downloaded and is ready to install on the server. To get updates with this choice you will have to click Check for updates located in the Version section.

The following information and options are in the Version section of the HP Update dialog. The server software version number and date are shown.

Click Check for updates to immediately check for available software updates, regardless of the configuration settings you selected above. The Install link becomes active when an update has been downloaded, but not installed.

Click Install to run the server update. The Rollback link becomes active when a software update has been installed. Use this link to uninstall the update on the server and revert to the previous server software version. Each home computer still needs to be updated or rolled back so that the server and client computers are running the same version of software. If your server does not have the correct software version, you will get an error message when you try to install the client software.

See Updating and Rolling Back the Server for more information. Once the server is updated, the client PC update is on the server and can be run from the software folder. The following sections describe various methods for installing the client PC update.

Click an option below to view the instructions for updating your client. Figure : Run Programs. Figure : HP Update. Click Next to immediately check for a client PC update. When the server software is updated, the new client executable file is placed on the server but not installed.

As long as you run the Software Installation Disc after you update the server, the CD will find the new client executable file on the server and install it.

Usually, you can temporarily disable a firewall to see if this is the cause. Sometimes multiple firewalls may be running on a PC, which isn't generally a good idea, so make sure you try disabling them all. A properly designed firewall should alert you the first time when an application is trying to use your network, and then allow you to enable it permanently but some will just quietly block applications without notifying the user.

If you are prompted to allow one of these applications to access your network, please do so and make sure that you allow it 'now and every time' it attempts to use the network. One Media Vault owner reported that Zone Alarm, despite having all of the MV apps in its 'allowed' list, still would silently block packets.

This makes ZoneAlarm to apply 'medium' policy, which permits incoming traffic. The quickest way to do this was to go to the event log, find a line describing a blocked MediaVault packet, then clicking "add to Zone" and then 'Trusted'. Your Media Vault and PC are on different subnets or have multiple network interfaces enabled.

If you have a network that has different subnets, which is possible if you are using Windows Internet Connection Sharing or multiple routers, the discovery mechanism may not be able to see your HP Media Vault because its broadcast packets won't go across a subnet. An example of two separate subnets would be if your PC had an IP address that began with Here is the procedure for doing that:. The file should have no extension. After you've confirmed that this works, it would be a good idea to set your HP Media Vault to a static IP address so that it doesn't get re-assigned with the DHCP function of your router and edit the file accordingly.

You've got MAC filtering enabled on your router. MAC IP filtering is a way to secure your network by only allowing a known list of devices to access to your network. Each time you get a new networked device, you must put an entry in the router's list to allow it access to the network. For example, if you install the Microsoft Loopback Adapter. If you have a wireless network card but are connected via a wired network interface, you may find that you have to disable the wireless interface to see the Media Vault.

Using Notepad or similar text editor, add a single line of text with this entry:. You should use the actual name and IP address of your MediaVault. If that causes the MediaVault to start responding, you may elect to just leave things 'as is' and depend on the lmhosts file to resolve the name for you.

If that was set to 'disable', then it was likely the source of the problem and you can remove the hpmediavault entry from lmhosts file and it should continue working. If you find that removing hpmediavault from lmhosts causes the problem to return, then it may be that your system's firewall is blocking NetBIOS packets which use ports , which is the default behavior on many firewalls today such as OneCare, Zone Alarm, and Norton If you are sure it's not a firewall issue, than your system may be set up with the wrong DhcpNodeType.

Discovered by Alan B. This first section applies to the MV1. The MV2 section is below under the dashes It should take about 3 minutes to finish. The latest official firmware version is 1. The systray firmware checker should make you aware of it if your FTP port is not blocked by a firewall. Its GPL source code will be available soon. You can get a copy of the firmware here.

The bug fixes in this version are listed here. The firmware resides partly in flash memory and partly on the System i. In the event that the System drive fails, it is necessary to restore this image using some special utilities that run on a PC over the network.

That's explained in the Hard Drive Replacement section. If it finds new firmware, it will prompt you to download it and install it. The software that came on the CDs, i. That utility runs once a month to look for updates for multiple HP products.

Note: Some Media Vaults shipped with firmware version 1. The 1. The HP MV2 series released with firmware version 1. However, if you want to replace or upgrade the drive in your existing MV2, you will need a way to download new firmware to it.

Please note that the MV1 and MV2 have completely different code bases and the numbering schemes are not related in any way. An MV2 firmware update utility is available on hp.

Please note also that when you put the MV2 in firmware update mode as explained in step 4 below, it may self-select an IP of That is normal. The download routine will be able to find it there. Slower network connections such as a 10 Mbps will not work. Instead, it will make it look as if the download was successful only to fail later.

Please be aware that this firmware utility is intended to place an image on a blank drive. There is a way to update the MV2 firmware and leave the data partition intact, but to do that, you must replace the recovery. Rename the existing recovery. You need to do that before launching the recovery program. Once you start renaming these files it can get confusing because they are exactly the same size and thus difficult to tell apart from each other.

The original recovery. Please note that the recovery. You need to have both files to perform a firmware update. Please make sure to have a backup of all your data because if anything goes wrong, your data may be lost.

This procedure, i. To use the recovery program, double click i. Similarly, you should run the MVFW To use the MV2 recovery program, you will need to follow the procedure below. There is a step-by-step method provided here that also comes with the utility:.

Note: if a second drive is installed at the time of the firmware recovery, a JBOD spanned volume will automatically be created on both drives.

However, if you are using the non-destructive recovery. It is to the left of the USB port. Use a push-pin, paper clip or other tool to hold the button in. Do not release either button for 5 seconds. Just follow the steps given by the utility. The install process can take minutes. This section applies to the MV2 only. There is a problem with Firefox where the color codes of the drives do not match up properly on both sides of the web interface.

The little boxes on the right hand side are black instead of matching the bars on the left hand side. There is a way to fix this by placing a new pixel. You can find a new file here: clearpixel. Evidently, the pixel HP used wasn't really transparent and so it turns black, at least on Firefox, but this file works on IE, Safari and Firefox.

Just rename that file to pixel. If you have FTP enabled and port 21 forwarded to the Media Vault, a sustained brute force attack can eventually cause it to hang. Usually, you'll see excessive hard drive activity before this occurs. It may take days or weeks to occur. In order to correct this, I've written scripts that will delete these files and the vsftpd. The scripts can be found here. Here are the instructions to install them:.

Unzip the two files startup. Log into the Media Vault using the procedure explained in the telnet section of this FAQ and execute the following commands don't type the comments in the parentheses, they're just there to let you know what you're doing :. Reboot the Media Vault either with the command 'reboot' or power cycle it with the power button. Log back into the Media Vault with telnet and do a "ps" process status command to confirm that the process called 'cleartmp' is running. It should look something like this in the process status list:.

Now your FTP logs will be cleared out every hour. The default behavior of the script is to append a copy of the vsftpd. If not, you can edit the cleartmp script and remove that command.

This is more thoroughly explained in the startup. These procedures were written to solve a single issue. If you have installed or want to install other custom software on your Media Vault, please use the method explained the Adding software section of the FAQ , and make the appropriate changes to these scripts. Both the HP Media Vault Generation 1 and Generation 2 run a Linux kernel and so are sometimes considered attractive targets for 'hacking'. We ask that discussions about hacking, especially those related to IPKG take place on the hacking group because these topics are likely to confuse anyone not familiar with the Linux operating system.

IPKG is a package installer that takes pre-compiled binaries from a repository and installs them on the system. They are convenient because you don't need to know anything about compiling source code to use them. But they are also in many cases untested with the HP Media Vault, so if you wish to experiment with them, you should proceed with caution. The generation 1 and generation 2 Media Vaults have completely different hardware and internal firmware.

Generation 1 devices mv, and have a Broadcom mipsel-based system-on-chip SOC with the OS residing on a cramfs partition on the hard drive. A cramfs file system is not writable, so all modifications have to be added to a writable partition on the hard drive, such as Volume1.

In the case of the MV2 devices, the OS is on a writable part of the hard drive which makes it easier to hack but it has more inherent risks associated with hacking it because you can modify the OS in a way that may be hard to undo.

When it comes to IPKG, especially with respect to the MV2, then one must exercise caution because there are so many of these IPKG packages available and installing them has the potential to modify the libraries on the OS partition on the hard drive, and there is no easy way to 'undo' an installation like there is on the MV1. The MV1 has a hard reset which severs the tie to the startup. The firmware reflashing tool is now available for the MV2, but it deletes all the data from the drive when it is used, so hacking while at the same time using the MV2 for its intended purpose, i.

In addition to hacks to add functionality, Martin Michlmayr has put together a web site on how to install a Debian distribution on the MV2 series.

Please be aware that this will remove the Media Vault's OS and user interface and turn the Media Vault into a general purpose Linux box. If the internal drive fails within the 1 year warranty period, you can arrange for an exchange repair by calling HP. If you're outside the U. Some people have wondered it if is possible to replace the internal drive if it were to fail outside the warranty period or just to upgrade a GB internal drive to a GB or GB drive.

It's not difficult to replace the internal drive, no more so than replacing an internal hard drive in a PC. After replacing the drive, you will have to re-install the operating system over the network using a special program called Nasload. More about that later.

If the secondary drive fails, it will be obvious because the you'll get warnings through the user interface and in the systray. However, if the main drive fails, the Media Vault will not boot up, so it will need to be replaced before you can interact with the media vault again.

You may refer to these instructions when replacing the internal drive. First lay the Media Vault on its side and remove the 3 back panel screws. Slide the side cover backward about an inch and lift it up away from the chassis. Disconnect the SATA data and power cables from the internal drive. Remove the drive from its bracket and replace the drive with an equivalent SATA drive and reverse the procedure to install it in the media vault.

If the media vault has a secondary drive that contains a mirror of Volume1, it works a little differently than it does with a single drive media vault. In the case where Volume1 was not mirrored, you will need to recreate Volume1 on the system drive and to do that, you should perform a hard reset after you've installed a blank drive and before running Nasload. In this case, the MediaVault will automatically rename the Shared Folders in the mobile rack drive to FileShare2, MediaShare2, so that you can access them.

If Volume1 was mirrored, you should perform the following steps with the mirrored drive left in its slot. If you're replacing the internal drive and don't have Volume1 mirrored, then just make sure to do the hard reset first or you'll also hear the beep after loading the OS.

If you find yourself in that situation, the beeper can be silenced from the System Settings page. Download and place the latest firmware image in the same directory. Open a DOS window and change to the directory to where the firmware image and utilities are located i.

If everything is working, you should see a response similar to this within about 10 seconds:. Attempting to download firmware to local subnet. Use control-c to exit. If you get an authentication failure while using Nasload, then your Media Vault has its administration password set.

The workaround for this would be to do a hard reset, which will clear the password, or you can execute the nasload command with these options substituting your admin username and password in those locations:. When the username and password are set, Nasload requires that the u and p are lowercase.

If you get an error code , it's because Nasload doesn't think that the drive is blank. You'll need to format it on another computer without putting a file system on it. Basically, the first 5 sectors should all be zeroed out for the Media Vault to think the drive is blank. This utility will find an HP Media Vault on the local network that is looking for a firmware image and download it.

It will take about 5 minutes for everything to complete. An HP Media Vault with a blank drive will only boot to the point that it illuminates the network link light and power button. It will respond to pings and tftp for downloading via Nasload, but will not respond other network protocols. The power button can only be used to turn the Media Vault on, but not off, so if you want to power it off when it has a blank drive it it, you'll have to unplug it.

Once the firmware is downloaded, wait about 5 minutes and it will reboot and behave normally again. To exit Nasload, it's necessary to use control-c in the DOS window or it will run indefinitely. If you didn't have a mirror, then you are done. In the event that you had Volume1 mirrored, you will get an error about a missing System drive and mirror. You can then remove the reference to the missing portion of the mirror using the remove mirror button in the Disk Settings Page.

This will make the Volume1 a basic volume on the mobile rack drive. You can then set up the mirror again, this time using the mobile rack drive as the base of the mirror and the internal System drive as its mirror which should be unallocated space at this point.

The operating system is always on the System i. If Nasload just sits there after typing in the command, it can be because a firewall is stopping it. Usually, disabling a firewall will fix this problem but there has been a report that with the built-in Windows firewall, it's necessary to enable it and specifically allow packets to pass on port 69 the tftp port or it won't work.

There is a wealth of documentation and support available for the HP Media Vault. In addition to the information you can find on this site, HP also has a lot of information on the hp. Maximum addressable limit of the media vault 1. The HP Media Vault series 1 has a limit of 1. This limit is due to the amount of DRAM it has to hold the metadata for the Reiserfs journaling file system along with DRAM space that needs to be reserved for other processes.

By raw capacity, it means that if you make a GB mirror using two GB drives, it counts as 1 TB toward this limit. You will get an error message to the effect of "Not enough memory to mount one or more pools" if you attempt to add disks much beyond this limit. This is not a hard limit but rather is dependent on the amount of physical memory that may be required for other tasks in conjunction the number of volumes and number of files on each volume.

There is little risk of going up to 1. There are reports that some have even mounted a pair of GB drives without getting an error message.

However, exceeding the limit may be a problem once the number of volumes and files increases so it's best not to push it much beyond the published limit of 1.

Due to a firmware limitation, the maximum individual drive size on the MV2 is 1 TB. If you attempt to install a drive larger than 1 TB, you will find that it cannot successfully be formatted. There are no known work-arounds for this issue. Part of it can be fixed by installing a new version of fdisk, but there are still some script limitations that prevent mirroring volumes larger than 1 TB.

It doesn't appear that HP will issue new firmware to address this issue. Those who have installed raw Debian distributions are not affected by this limit, but with a Debian distribution the MV2 becomes just a headless Linux device with no Web UI which suits some Linux enthusiasts, but not most MV customers.

You can find the forum here. Mirroring of data across two drives i. RAID 1 allows you to keep a copy of your data on two drives in the Media Vault so you won't lose it in the event that one of the drives fails. Although you can mirror across an internal drive and an external USB drive connected to the Media Vault, this is not recommended because USB drives have independent power supplies and can be off-line when the Media Vault is powered up and this confuses the process that keeps track of the mirror and will cause it to have to rebuild the mirror should it discover that the USB drive is powered on after the Media Vault has booted.

It's best to use the internal drives and mirror the System drive to the drive that goes in the Mobile Rack slot. That way you can guarantee that both drives will power up and down at the same time. You can mirror multiple volumes across two drives, but most often the default volume i. Mirroring requires twice the disk capacity of a basic non-mirrored volume. In other words, if you want to make a mirror of a GB volume, you need another disk with GB of unallocated space.

You shouldn't think of a mirror as a backup for all potential causes of data loss. It only protects you from a hard drive failure inside the Media Vault.

You should always have another copy, preferably off-site, of any critical data. To mirror a drive, go to the Drive Setting page in the web interface and select a volume you wish to mirror. If the mirror button is grayed out, it probably means that there are no drives with enough free space to mirror the volume you've selected. You can resize or delete volumes on the destination drive to make room to accept the mirror. If your source volume is exactly the same size as the unallocated space, you may need to resize it to be slightly smaller to account for round-off errors when computing the unallocated space available.

If you formatted a drive you installed in the mobile rack, then it will likely contain a simple volume that occupies the entire drive. You will either need to delete this volume, or resize it to make room for Volume1, if you're trying to mirror Volume1 to the mobile rack drive. After you've selected the volume to mirror and the destination drive for the mirror, it will take several minutes to set up the partitions before the web page will refresh.

Then in the background, it will copy the data on one drive to the other. During this time, the Media Vault will be available with minimal affect on performance for most tasks. A GB drive will take about 12 hours to mirror but there are a few ways to speed this up. A method you can use if you don't have much data on the Volume you're mirroring is to first resize it to a smaller volume and then create the mirror, and then resize the mirrored volume to full size.

Using this method you can create a GB mirror in about 10 minutes if you are able to resize to something very small like 2 GB.

The reason for this is that the mirroring process doesn't really know what data to copy so it just copies all the blocks on the base volume to the mirror. In the case of resizing a mirror, the process understands that the new area created will be blank, so it knows not to spend any time copying that portion of the disk.

Another way to speed up the process, albeit at the expense of overall performance for other tasks, is to change a few variables. Do do this you need to telnet into the Media Vault and execute these two commands:. They will revert to those values when you power cycle the Media Vault.

Speeding up mirroring using this procedure will slow down file transfers so it should be used only if you don't intend to be doing anything else for a while with the Media Vault. This tip was provided by Pedro B. In the event that a mirrored drive fails, the procedure for getting your data from the mirror is covered in the Hard Drive Replacement section of the FAQ.

Should the Media Vault ever become non-operational due to a motherboard or power supply failure, it's possible that the data on the drives is still intact and could be retrieved by mounting them in another Media Vault. If you are skilled in Linux, there is also a is a technique to mount an MV1 drive on a Linux system covered in this section of the FAQ.

In the case of the MV2, the file system is completely different than the MV1 since they run different processors, Linux kernels, and underlying code to control the device. The MV1 and MV2 drives cannot be interchanged. Because of this, you need to perform some extra steps to mount it on a Linux system.

Then use the pvs command to find the logical volume name s. Then use the lvdisplay command to get the full name of the volume. An example of commands to do this are shown below please note, the volume names are unique to each drive and the example below is just an example. You should use the names that are shown by the pvs and lvdisplay commands on your Linux system :.

If you need more flexibility than the GUI offers, you can make a mount point directory and mount the HP Media Vault's folders directly. Is my Windows version bit or bit? I don't see my operating system. Detected operating system: Selected operating system: Select your operating system and version , Change. Let us detect the drivers you need for this HP PC Our automated tool will simplify the choices you have to make Detect my drivers.

Let us detect the drivers you need for this HP PC Skip the confusion of sorting through all of our drivers and let us detect only the ones you need.

Detect my drivers. Learn more Continue. Show location. HP Support Solution Framework is downloading Locate the file in your browser window, and double-click to begin installing. Please wait while we find your drivers. Detection not available. Product detection timed out. Please try again. Download list: Download selected files. Email my list. Remove all. Detection completed.

Here are the drivers available for your system. All drivers. Filter by importance. Open download list Open all. Let HP identify any out-of-date or missing drivers and software How does HP use product data collected with this service? Choose 'Refresh' to update the list. My download list. Select all Deselect all. Select the desired files and choose 'Download files' to start a batch download. Select your desired files and a list of links will be sent by email. One of the advantages of the system is that if the primary drive is lost which includes some system software which works in conjunction with the firmware the system can be restored onto a replacement SATA hard drive using HP's nasrecovery software.

If the issue still persists, then I suggest that you contact the device manufacturer for further assistance. Swathi B - Microsoft Support. Visit our Microsoft Answers Feedback Forum and let us know what you think.



0コメント

  • 1000 / 1000